Silesian University of Technology, Gliwice, Poland, EU
The Microstructure and Properties of Magnesium Alloys Mg-Li-Ca after the Process of Extrusion - POSTER
PB2
CHYŁA Paweł
AGH University of Science and Technology, Cracow, Poland, EU
A Complex Analysis of the Influence of Process and Geometric Parameters on the ECAP Process for Al Alloys of the 2XXX Series Using the Finite Element Method - POSTER
PB3
CHYŁA Piotr
AGH University of Science and Technology, Cracow, Poland, EU
Constitutive Equation to Predict the Flow Stress and the Processing Maps of the NI55CR45 Alloy - POSTER
PB4
DROBNE Matej
Valji d.o.o., Štore, Slovenia, EU
Thermal Crack Propagation During Hot Rolling and its Influence on Cast Iron Work Roll Degradation - POSTER
PB5
DUCKI Kazimierz
Silesian University of Technology, Katowice, Poland, EU
The Characteristic of Deformability of Ni-Fe Superalloy During High-Temperature Deformation - POSTER
PB6
GORONKOVA Aigul
Ufa State Petroleum Technological University, Ufa, Russian Federation
Peculiarities of Superplastic Forming of the Rectangular Edge Welded Envelope - POSTER
PB7
GREGER Miroslav
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Development of Structure of the Steel EN X160CrMoV 12 1 at Forging on Radial Forging Machines and on Hydraulic Presses - POSTER
PB8
GRZEBINOGA Justyna
AGH University of Science and Technology, Kraków, Poland, EU
Finite Element Analysis of Pressure Forming of Thin-walled Aluminum Heat Exchangers - POSTER
PB9
HADASIK Eugeniusz
Silesian University of Technology, Katowice, Poland, EU
Influence of Hot Deformation on Microstructure and Plastic Properties of Mg-Al-Zn-Mn Type Alloy - POSTER
PB10
HEIDARI GHALEH Milad
Yasaman Partov Ghaem Co, Iran, Sary, Iran, Islamic Republic of
Effect of Cooling Rate on Quenched & Tempered Rebar Steel Properties - POSTER
PB11
ISUPOV Fedor
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
Simulation and Practical Implementation of the Powder Deformation Processes in Shells - POSTER
PB12
KASZUBA Marcin
Wroclaw University of Technology, Wroclaw, Poland, EU
Application of ZeroFlow Nitriding Method in Improvement of Durability of Forging Tools - POSTER
PB13
KAWAŁEK Anna
Czestochowa University of Technology, Częstochowa, Poland, EU
Analysis of the Effect of the Asymmetric Rolling Process on the Development of the Microstructure of Low-carbon Steels with Micro-additives - POSTER
PB14
KOREČEK David
Technical University of Liberec, Faculty of Mechanical Engineering, Department of Engineering Technology, Liberec, Czech Republic, EU
Numerical Models for Predicting Spring-Back of Stamped Titanium Alloy - POSTER
PB15
KUC Dariusz
Silesian University of Technology, Katowice, Poland, EU
Influence of Annealing on Microstructure and Properties of Cold Rolled Shed from High Mn-Al Steel Type - POSTER
PB16
LABER Konrad
Czestochowa University of Technology, Czestochowa, Poland, EU
Numerical Modelling of Torsion Testing on the STD 812 Torsion Plastometer - POSTER
PB17
MALINOWSKI Tomasz
Pratt & Whitney Rzeszow / Rzeszow University of Technology, Rzeszów, Poland, EU
Two-Stage Rubber-Pad Based Forming of Fan Engine Bearing Housing - POSTER
PB18
MIŁEK Tomasz
Kielce University of Technology, Kielce, Poland, EU
Effect of the Upsetting Ratio on Wall Thickness Distribution in Longitudinal Section of Hydromechanically Bulged Axisymmetric Components Made from Copper Tubes - POSTER
PB19
MRZYGŁÓD Barbara
AGH University of Science and Technology, Cracow, Poland, EU
Sensitivity Analysis of the Artificial Neural Network Inputs in a System to Durability Prediction of Forging Tools - POSTER
PB20
NIEWIELSKI Grzegorz
Politechnika Slaska, Gliwice, Poland, EU
Influence of Hot Working and Cooling Conditons on the Microstructure and Properties of C70D Steell for Wire Rod - POSTER
PB21
NOWAK Andrzej
AGH University of Science and Technology, Kraków, Poland, EU
Influence of the Continuous Casting Parameters on the Properties of Brass for Plastic Processing - POSTER
PB22
OPĚLA Petr
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Determination of the Critical Strain for the Onset of Dynamic Recrystallization of C45 Carbon Steel using Flow Stress Models - POSTER
PB23
PAČÁK Tomáš
Czech Technical University in Prague, Prague, Czech Republic, EU
Methodology of the Springback Compensation in Sheet Metal Forming Processes - POSTER
PB24
PIEJA Tomasz
Pratt & Whitney Rzeszow / Rzeszow Univeristy of Technology, Rzeszow, Poland, EU
Numerical Analysis of Cooling System in Warm Metal Forming Process - POSTER
PB25
PRESZ Wojciech
Warsaw University of Technology Institute of Manufacturing Technologies, Warsaw, Poland, EU
Application of Complex Micro-die for Extrusion of Micro-rivets for Micro-joining - POSTER
PB26
PRESZ Wojciech
Warsaw University of Technology, Warsaw, Poland, EU
Ultrasonic Assisted Microforming - POSTER
PB27
RUSZ Stanislav
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Increasing the Quality of Steel DC01 by DRECE Method - POSTER
PB28
RUSZ Stanislav
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Influence of Initial Structure on Stress-Strain Curves of Medium-Carbon Steel - POSTER
PB29
SCHREK Alexander
Slovak University of Technology in Bratislava, Faculty of Mechanical Engineering, Bratislava, Slovakia, EU
Forming and Deformation Properties of Drawn Part B-pillar Reinforcement from Simple Blank and Alternatively Tailor-welded Blank - POSTER
PB30
SOBOTKA Jiří
Technical University of Liberec, Faculty of Mechanical Engineering , Liberec, Czech Republic, EU
Influence of Deformation on the Hardness Distribution for Car-bodies Materials - POSTER
PB31
TERENTYEV Maxim
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
Prediction of Stress-Strain Curve Behavior of a Modified Nimonic 263 Superalloy - POSTER
PB32
THOMAS Piotr
Kielce University of Technology, Kielce, Poland, EU
Effect of Friction on the Punch Force During Combination Extrusion of Enaw-1050A Aluminum Alloy - POSTER
PB33
VALEŠ Michal
Czech Technical University in Prague, Prague, Czech Republic, EU
Feasibility Study of Manufacturing Outer Car Body Parts with Use of DP500 - POSTER
PB34
VOTAVOVÁ Helena
Brno University of Technology, Brno, Czech Republic, EU
Effect of the Speed of Feedstock on Heat Transfer Coefficient durign Descaling in Hot Rolling - POSTER
PB35
ZHUCHKOVA Tatiana
Lipetsk State Technical University, Lipetsk, Russian Federation
Study of Recrystallization Kinetics during and after Hot Deformation depending on Deformation Conditions for C45 Steel - POSTER
